Vehicle
Wiring Details for your
2009-2011 Mazda Mazda 6 Wiring Diagram |
Printer Friendly
Version |
|
|
Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 2009-2011 Mazda Mazda 6 . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle. Please be sure to test all of your wires with a digital multimeter before making any connections. More information on using a multimeter and testing wires please see our Technical Support Area.
|
|
|
 |
| PART |
COLOR |
LOCATION |
| 12 VOLT
CONSTANT |
RED/BLUE (+) |
@ IGNITION SWITCH, (6-PIN PLUG), PIN F |
| STARTER |
GRAY/RED (+), NOTE #6 |
@ IGNITION SWITCH, (6-PIN PLUG), PIN A |
| STARTER
2 |
BLACK/GREEN and BLACK/RED (-) (PUSH-BUTTON START) |
@ PUSH-BUTTON START SWITCH or KCM, (12-PIN PLUG), PINS J and K, NOTE #10 |
| IGNITION
1 |
GREEN/YELLOW (+), NOTE #7 |
@ IGNITION SWITCH, (6-PIN PLUG), PIN C |
| IGNITION
2 |
N/A |
|
| IGNITION
3 |
N/A |
|
| ACCESSORY/HEATER
BLOWER 1 |
PINK/YELLOW (+), NOTE #8 |
@ IGNITION SWITCH, (6-PIN PLUG), PIN B |
| ACCESSORY/HEATER
BLOWER 2 |
YELLOW (+), NOTE #9 |
@ IGNITION SWITCH, (6-PIN PLUG), PIN D |
| KEYSENSE |
N/A |
|
| PARKING
LIGHTS ( - ) |
BLACK/WHITE (-) |
@ HEADLIGHT SWITCH, (17-PIN PLUG), PIN L |
| PARKING
LIGHTS ( + ) |
RED/BLUE (+) |
@ BCM,(16-PIN PLUG(8), PIN O, NOTE #2 |
| POWER LOCK |
BLACK/WHITE (TYPE B)(-)Negative , NOTE #3 |
@ BCM,(16-PIN PLUG(6), PIN G, NOTE #2 |
| POWER UNLOCK |
Use LOCK wire |
|
| DOOR TRIGGER |
BLACK/YELLOW (-) N.C. |
@ BCM,(16-PIN PLUG(8), PIN B, NOTE #2 |
| DOMELIGHT
SUPERVISION |
BLACK/BLUE (-) |
@ BCM,(16-PIN PLUG(6), PIN M, NOTE #2 |
| TRUNK RELEASE |
BLACK/RED (-) |
@ BCM,(30-PIN PLUG(3), PIN X, NOTE #2 |
| SLIDING
POWER DOOR |
N/A |
|
| HORN |
BLACK (-) |
@ BCM,(30-PIN PLUG(3), PIN V, NOTE #2 |
| TACH |
Any wire NOT RED(4 Cyl) or BLUE(V6) (AC) |
@ Any FUEL-INJECTOR |
| WAIT TO
START LIGHT |
N/A |
|
| BRAKE |
RED/WHITE (+) |
@ BRAKE PEDAL SWITCH or in DRIVERS KICK PANEL, Harness to REAR of Vehicle |
| FACTORY
ALARM DISARM |
Disarms with INTERFACE MODULE, See NOTE #4 |
|
| ANTI-THEFT |
MAZDA'S TRANSPONDER ANTI-THEFT SYSTEM, See NOTE #1 |
|
| EXTRA
INFORMATION |
| NOTE #1: This vehicle is with MAZDA'S TRANSPONDER ANTI-THEFT SYSTEM,
for REMOTE STARTING ONLY you will need the Part #791 BYPASS Module and an
Extra Ignition key. (Requires extra key for Operation)
Part # PK-ALL or PKFM for REMOTE STARTING ONLY, requires 2 keys for
programming, NO key required for Operation.
Part # DB-ALL for Remote Starting and Keyless Entry operation (no resistors
required), 2 keys required for programming, no key required for Operation.
To Order the go to the SECURITY BYPASS MODULE Page or INTERFACE BYPASS
MODULE Page on this website.
NOTE #2: the BCM, (Body Control Module) is located in the DRIVERS KICK PANEL.
NOTE #3: This Vehicle requires a INTERFACE BYPASS MODULE for the KEYLESS ENTRY Function
NOTE #4: this Vehicle ARMS/DISARMS with INTERFACE BYPASS MODULE
NOTE #5: TEST this wire while Opening the Trunk/Liftgate from the Release Button on the
REAR of the Vehicle.
NOTE #6: On vehicles with the PUSH-BUTTON Start, this wire is at the KCM, (GRAY, 27-PIN
PLUG), PIN B. The KCM (Keyless Control Module) is located under the Drivers Dash
NOTE #7: On vehicles with the PUSH-BUTTON Start, this wire is a PINK/BLUE (+)located at the
RELAY BLOCK, (6-PIN PLUG), PIN B. The RELAY BLOCK is located under the DRIVERS
DASH, close to the Steering Column.
NOTE #8: On vehicles with the PUSH-BUTTON Start, this wire is located at the RELAY BLOCK,
(6-PIN PLUG), PIN F. The RELAY BLOCK is located under the DRIVERS DASH and to
the LEFT of the Steering Column.
NOTE #9: On vehicles with the PUSH-BUTTON Start, this wire is located at the RELAY BLOCK,
(8-PIN PLUG), PIN B. The RELAY BLOCK is located under the DRIVERS DASH and to
the LEFT of the Steering Column.
NOTE #10: The KCM (Keyless Control Module) is located under the Drivers Dash
|
|
|
|
|
|
